? semiconductor components industries, llc, 2014 december, 2014 ? rev. 0 1 publication order number: NHPM120/d NHPM120, nrvhpm120 surface mount ultra fast power rectifier powermite ? power surface mount package this ultrafast powermite provides soft recovery fast switching performance in a compact thermally efficient package. the advanced packaging techniques provide for a very efficient micro?miniature space?saving surface mount rectifier. with its unique heatsink design, the powermite offers thermal performance similar to the sma while being 50% smaller in footprint area. features ? fast soft switching for reduced emi and higher efficiency ? low profile ? maximum height of 1.1 mm ? small footprint ? footprint area of 8.45 mm 2 ? supplied in 12 mm tape and reel ? low thermal resistance with direct thermal path of die on exposed cathode heat sink ? nrv prefix for automotive and other applications requiring unique site and control change requirements; aec?q101 qualified and ppap capable ? these devices are pb?free, halogen free/bfr free and are rohs compliant mechanical characteristics: ? powermite is jedec registered as d0?216aa ? case: molded epoxy ? epoxy meets ul 94 v?0 @ 0.125 in ? weight: 16.3 mg (approximately) ? lead and mounting surface temperature for soldering purposes: 260 c maximum for 10 seconds ? msl 1 applications ? automotive led lighting ? engine control ? freewheeling diode where space is at a premium ? flat panel display ordering information ultrafast rectifier 1.0 ampere, 200 volts http://onsemi.com device package shipping ? NHPM120t3g powermite (pb?free) 12000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specification s brochure, brd8011/d. powermite case 457 cathode anode marking diagram m = date code p12 = device code = pb?free package m p12 12 nrvhpm120t3g powermite (pb?free) 12000 / tape & reel
NHPM120, nrvhpm120 http://onsemi.com 2 maximum ratings rating symbol value unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 200 v average rectified forward current (t l = 165 c) i o 1.0 a peak repetitive forward current (rated v r , square wave, 20 khz) t l = 165 c i frm 2.0 a non?repetitive peak surge current (surge applied at rated load conditions halfwave, single phase, 60 hz) i fsm 30 a storage and operating junction temperature range (note 1) t stg , t j ?65 to +175 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. the heat generated must be less than the thermal conductivity from junction?to?ambient: dp d /dt j < 1/r ja . thermal characteristics characteristic symbol value unit thermal resistance, junction?to?lead (note 2) jcl 12 c/w thermal resistance, junction?to?ambient (note 2) r ja 75 c/w thermal resistance, junction?to?ambient (note 3) r ja 260 c/w electrical characteristics characteristic symbol value unit maximum instantaneous forward voltage (note 4) (i f = 1.0 a, t j = 25 c) (i f = 2.0 a, t j = 25 c) (i f = 1.0 a, t j = 125 c) (i f = 2.0 a, t j = 125 c) v f 1.0 1.1 0.85 0.95 v maximum instantaneous reverse current (note 4) (rated dc voltage, t j = 25 c) (rated dc voltage, t j = 125 c) i r 0.5 25 a reverse recovery time i f = 1.0 a, v r = 30 v, dl/dt = 50 a/ s, t j = 25 c t rr 25 ns reverse recovery time i f = 1.0 a, v r = 30 v, dl/dt = 50 a/ s, t j = 50 c t rr 50 ns product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 2. mounted with 700 mm 2 copper pad size (approximately 1 in 2 ) 1 oz fr4 board. 3. mounted with pad size approximately 20 mm 2 copper, 1 oz fr4 board. 4. pulse test: pulse width 380 s, duty cycle 2.0%.
NHPM120, nrvhpm120 http://onsemi.com 3 typical characteristics figure 1. typical instantaneous forward characteristics figure 2. maximum instantaneous forward characteristics v f , instantaneous forward voltage (v) v f , instantaneous forward voltage (v) 1.1 0.9 0.7 0.5 0.3 0.1 0.001 1 10 100 1.2 0.8 0.6 0.2 0 0.001 1 10 100 figure 3. typical reverse characteristics figure 4. maximum reverse characteristics v r , instantaneous reverse voltage (v) v r , instantaneous reverse voltage (v) 180 120 100 80 60 40 20 0 1.e?12 200 140 120 80 40 20 0 figure 5. typical junction capacitance v r , reverse voltage (v) 0 10 100 1000 i f , instantaneous forward current (a) i r , instantaneous reverse current (a) c, junction capacitance (pf) 1.4 i f , instantaneous forward current (a) 140 200 1.e?11 1.e?09 1.e?08 1.e?06 1.e?05 1.e?03 60 100 1.e?08 1.e?07 1.e?05 1.e?03 i r , instantaneous reverse current (a) 20 200 t a = 175 c t a = 125 c t a = ?40 c t a = 25 c t a = 150 c t a = 125 c t a = ?40 c t a = 25 c t a = 150 c t a = 125 c t a = 25 c 1.e?04 figure 6. current derating t c , case temperature ( c) 100 60 160 140 20 0 0 0.5 1.5 2.0 i f(av) , average forward current (a) 40 120 square wave dc r jc = 12 c/w t j = 25 c 1.5 0.4 1.0 160 t a = 150 c t a = 175 c t a = 175 c 0.1 0.01 0.1 0.01 t a = ?40 c 1.e?10 1.e?07 1.e?04 160 t a = 150 c t a = 125 c t a = 25 c t a = 175 c t a = ?40 c 180 40 60 80 100 120 140 160 180 1.0 80 180 1.e?06 1.e?09 1.e?10 1.3 1
NHPM120, nrvhpm120 http://onsemi.com 4 typical characteristics figure 7. forward power dissipation i f(av) , average forward current (a) 1.2 0 0 1.0 3.0 p f(av) , average forward power dissipation (w) t j = 175 c square wave dc i pk /i av = 5 i pk /i av = 20 i pk /i av = 10 0.2 0.6 0.8 0.5 1.5 2.0 2.5 0.4 1.0 0.1 0.00001 pulse time (s) 100 10 0.1 0.01 0.0001 0.001 0.01 1.0 10 100 0.000001 50% (duty cycle) 25% 10% 5.0% 2.0% 1.0% single pulse 1000 r(t) (c/w) 1.0 0.1 0.00001 pulse time (s) 100 10 0.1 0.01 0.0001 0.001 0.01 1.0 10 100 0.000001 50% (duty cycle) 25% 10% 5.0% 2.0% 1.0% single pulse 1000 r(t) (c/w) figure 8. thermal response, junction?to?ambient (20 mm 2 pad) 1.0 1000 figure 9. thermal response, junction?to?ambient (1 in 2 pad)
NHPM120, nrvhpm120 http://onsemi.com 5 package dimensions powermite case 457?04 issue f dim min max min max inches millimeters a 1.75 2.05 0.069 0.081 b 1.75 2.18 0.069 0.086 c 0.85 1.15 0.033 0.045 d 0.40 0.69 0.016 0.027 f 0.70 1.00 0.028 0.039 h -0.05 +0.10 -0.002 +0.004 j 0.10 0.25 0.004 0.010 k 3.60 3.90 0.142 0.154 l 0.50 0.80 0.020 0.031 r 1.20 1.50 0.047 0.059 s notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold flash, protrusions or gate burrs. mold flash, protrusions or gate burrs shall not exceed 0.15 (0.006) per side. s b m 0.08 (0.003) c s t ?a? ?b? s j k ?t? h l j c d s b m 0.08 (0.003) c s t f pin 1 pin 2 r 0.50 ref 0.019 ref 2.54 0.100 0.635 0.025 1.27 0.050 2.67 0.105 0.762 0.030 mm inches scale 10:1 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 NHPM120/d powermite is a registered trademark of and used under a license from microsemi corporation. literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative
|
